Aqua PU 17-06
/

Product Description

A two-component modified ester polyol aliphatic polyurethane coating, designed to provide excellent weathering resistance for longer colour and shade retention. Exhibits excellent UV resistance, water resistance and recoatability.

  • Extensive Applications
  • High Aesthetics
  • Excellent weather proof and UV Resistance
  • Low Permeability
  • Easy to maintain
  • Durable
  • Extensive Range of Colours

POSSIBLE APPLICATIONS

Aqua PU 17-06 is suitable for use in both new construction and as a maintenance coating which can be used in a wide variety of environments including offshore structures, chemical and petrochemical plants, bridges, pulp and paper mills, and in the power industry.

Product Information

Colour All RAL, BS colour
Finish Glossy
Volume Solids 50 ± 3%
Mixing Ratio 9 :1 (Part A : Part B)- By volume
Volume Solids 100% (ASTM 2697)
Pot Life 3 – 4 hours @ 30° C
Typical Film Thickness 50μ dry
Theoretical Coverage 11 m /liter at 50μ DFT
Method of Application Airless spray, Conventional Spray, Brush, Roller
Touch Dry 30-60 minutes
Dry to Handle 4-6 hours at 30° C
Hard Dry 12 hours at 30° C
Full Cure 7 days

Overcoating Condition

Minimum Over-coating Period 4 hours
Maximum Over-coating Period 72 hours*
Surface should be clean and dry prior to over-coating. If Aqua PU has been exposed for long periods, fresh water washing should be conducted before application of any coatings.

Systems and Compatibility

  • Can be applied as finish coat on following products.
  • Aqua ST-03 Aqua Sealer Aqua ST Aqua Mastic
  • Please consult Flosil-BET Coatings (India) Pvt Ltd for further product recommendations.

PERFORMANCE DATA

Abrasion Resistance Max 90mg weight loss per 1000 cycles - 1kg load - CS10 Wheel - ASTM D4060
Impact Resistance 27 Joule - ASTM D2794
Pull - Off Adhesion 10.66 Mpa - ASTM D4541
Scratch Hardness 12.5 kg Load - No Failure - (BS3900 Part E2)
Salt Fog Resistance Excellent, Unaffected after 3000 hr Exposure - ASTM B117
Cyclic Fog / UV Exposure Excellent, Unaffected after 3000 hr Exposure - ASTM 5894-05

Surface Preparation

All surfaces to be coated shall be dry and free from oil, grease, dust, dirt and any foreign matter that can adversely affect adhesion of coating. Solvent cleaning as per SSPC SP1 shall be conducted wherever necessary.

Mixing

Aqua PU 17-06 is supplied in 2 parts. Always mix curing agent (Part B) into the liquid binder (Part A) while stirring. 75-100 RPM mixer is recommended. Material should be screened prior to application.

Thinning

Aqua T02 - 10 to 20% as Needed

Airless Spray

Recommended, Tip range: 0.43-0.53 mm at 2500 - 3000 psi tip pressure. Remove filters from the spray equipment to avoid blockages

Conventional Spray

Recommended. Do not exceed spray pressur e than 4 Kg/Cm2. Remove filters from the spray equipment to avoid blockages.

Brush / Roller

Recommended to use roller and brush.

IDEAL APPLICATION AMBIENT CONDITIONS

Air Temperature 5-55° C
Substrate Temperature 5-65% C
Relative Humidity 50% minimum, 85% maximum
Surface temperature shall always be at least 3°C above Dew Point. Do not expose the coated articles where there are chances of condensation on the surface.

Availablity & Packing Size

  • Available wor ldwide through Flosi l -BET Coatings (India) Pvt Ltd.
  • Packing Size = 4 Liters, Bulk pack sizes are available on request.
  • Shelf Life: 12 Months* from the date of manufacturing (Material to be stored in sealed and unopened containers in closed shelter.)

IMPORTANT NOTE

The information in this data sheet is not intended to be exhaustive. Any person using this product for any purpose other than that specifically recommended either in this data sheet or by authorized representatives of Flosil-BET does so at their own risk. All advice given or statement made about the product (whether in the data sheet or otherwise) is correct to our knowledge, however, we have no control on the quality and condition of the substrate being coated with this product and hence Flosil-BET does not assume any liability arising out of misuse of this product. All safety precautions must be taken while handling of this product. Please refer to MSDS for more details.

CONTACT /
GET IN TOUCH WITH US
Flosil-BET

No:40, Velichai Village,
Vandalur – Kelambakkam Road,
Chennai – 600 048.